EVPN Virtual Ethernet Segment

Ethernet VPN (EVPN, ) and Provider Backbone EVPN (PBB-EVPN, )) introduce a comprehensive suite of solutions for delivering Ethernet services over MPLS/IP networks. These solutions offer advanced features, including multi-homing capabilities. Specifically, they support Single-Active and All-Active redundancy modes for an Ethernet Segment (ES). As defined in , an Ethernet Segment (ES) represents a collection of Ethernet links that connect a customer site to one or more PEs devices. This document extends the concept of an Ethernet Segment by allowing an ES to be associated with a set of Ethernet Virtual Circuits (EVCs, such as VLANs) or other entities, including MPLS Label Switched Paths (LSPs) or Pseudowires (PWs). This extended concept is referred to as Virtual Ethernet Segments (vES). This draft outlines the requirements and necessary extensions to support vES in both EVPN and PBB-EVPN. The scope of this document includes PBB-EVPN , EVPN over MPLS , and EVPN over IP . However, it excludes EVPN over SRv6 .

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 when, and only when, they appear in all capitals, as shown here.

Some Service Providers (SPs) seek to extend the concept of physical Ethernet links in an ES to encompass Ethernet Virtual Circuits (EVCs), wherein multiple EVCs (such as VLANs) can be aggregated onto a single physical External Network-to-Network Interface (ENNI). An ES composed of a set of EVCs rather than physical links is referred to as a virtual ES (vES). Figure 1 illustrates two PE devices (PE1 and PE2), each with an ENNI aggregating several EVCs. Some of these EVCs on a given ENNI can be associated with vESes. For instance, the multi-homed vES depicted in Figure 1 consists of EVC4 on ENNI1 and EVC5 on ENNI2.

<---- EVPN Network -----> <-802.1Q-> Figure 1: Dual-homed Device/Network (both SA/AA) and SH on same ENNI ]]> ENNIs are commonly used to reach remote customer sites via independent Ethernet access networks or third- party Ethernet Access Providers (EAP). ENNIs can aggregate traffic from many vESes (e.g., hundreds to thousands), where each vES is represented by its associated EVC on that ENNI. As a result, ENNIs and their associated EVCs are a key element of SP external boundaries that are carefully designed and closely monitored. As a reminder, the ENNI is the demarcation between the SP (IP/MPLS Core Network) and the third-party Ethernet Access Provider. To meet customers' Service Level Agreements (SLA), SPs build redundancy via multiple EVPN PEs and across multiple ENNIs (as shown in Figure 1) where a given vES can be multi&nbhy;homed to two or more EVPN PE devices (on two or more ENNIs) via their associated EVCs. Just like physical ESs in and solutions, these vESes can be single&nbhy;homed or multi&nbhy;homed ESs and when multi&nbhy;homed, then can operate in either Single-Active or All-Active redundancy modes. In a typical SP external-boundary scenario (e.g., with an EAP), an ENNI can be associated with several thousands of single&nbhy;homed vESes, several hundreds of Single- Active vESes and it may also be associated with tens or hundreds of All-Active vESes. The specific figures (hundreds, thousands, etc.) used throughout this document reflect the relative quantities of various elements as understood at the time of writing.

Other Service Providers (SPs) want to extend the concept of the physical links in an ES to individual Pseudowires (PWs) or to MPLS Label Switched Paths (LSPs) in Access MPLS networks - i.e., a vES consisting of a set of PWs or a set of LSPs. Figure 2 illustrates this concept.

<-----MPLS Agg----> <--- EVPN Network ---> <-802.1Q-> Figure 2: Dual-Homed and Single-homed Network on MPLS Aggregation networks ]]> In certain scenarios, Service Providers utilize MPLS Aggregation Networks that are managed by separate administrative entities or third-party organizations to gain access to their own IP/MPLS core network infrastructure. This situation is depicted in Figure 2. In such scenarios, a virtual ES (vES) is defined as a set of individual PWs when aggregation is not feasible. If aggregation is possible, the vES can be associated with a group of PWs that share the same unidirectional LSP pair, where the LSP pair consists of the ingress and egress LSPs between the same endpoints. In the example of Figure 2, EVC3 is connected to a VPWS instance in AG2 that is connected to PE1 and PE2 via PW3 and PW5 respectively. EVC4 is connected to another VPWS instance on AG2 that is connected to PE1 and PE2 via PW4 and PW6, respectively. Since the PWs for the two VPWS instances can be aggregated into the same LSP pair going to and coming from the MPLS network, a common virtual ES (vES) can be defined for the four mentioned PWs. In Figure 2, LSP1 and LSP2 represent the two LSP pairs between PE1 and AG2, and between PE2 and AG2, respectively. The vES consists of these two LSP pairs (LSP1 and LSP2) and each LSP pair has two PWs. This vES will be shared by two separate EVPN instances (e.g., EVI-1 and EVI-2) in the EVPN network. PW3 and PW4 are associated with EVI-1 and EVI-2 respectively on PE1, and PW5 and PW6 are associated with EVI-1 and EVI-2 respectively on PE2. In some cases, the aggregation of PWs that share the same LSP pair may not be possible. For instance, if PW3 were terminated into a third PE, e.g. PE3, instead of PE1, the vES would need to be defined on a per individual PW on each PE. For MPLS/IP access networks where a vES represents a set of LSP pairs or a set of PWs, this document extends the Single-Active multi-homing procedures defined in and to accommodate vES. The extension of vES to support All-Active multi-homing in MPLS/IP access networks is beyond the scope of this document. This draft defines the concept of a vES and outlines the additional extensions necessary to support a vES in accordance with and . enumerates the set of requirements for a vES. details the extensions for a vES applicable to EVPN solutions, including those specified in and . These extensions are designed to meet the requirements outlined in . also provides an overview of the solution, while addresses failure handling, recovery, scalability, and fast convergence of and for vESes.

Attachment Circuit Backbone MAC Address Customer Edge Device Customer/Client MAC Address Designated Forwarder External Network-Network Interface Ethernet Segment Ethernet Segment Identifier Ethernet Auto-Discovery Route Ethernet Virtual Circuit, EVPN Instance Ethernet VPN Service Instance Identifier (24 bits and global within a PBB network see ) Provider Backbone Bridge Provider Backbone Bridge EVPN Provider Edge Device Virtual Pseudowire Service When only a single PE, among a group of PEs attached to an Ethernet Segment, is allowed to forward traffic to/from that Ethernet Segment, then the Ethernet Segment is defined to be operating in Single-Active redundancy mode. When all PEs attached to an Ethernet segment, are allowed to forward traffic to/from that Ethernet Segment, then the Ethernet Segment is defined to be operating in All-Active redundancy mode.

This section describes the requirements specific to virtual Ethernet Segment (vES) for (PBB-)EVPN solutions. These requirements are in addition to the ones described in , , and .

A PE device MUST support the following types of virtual Ethernet Segments (vES): (R1a) The PE MUST handle single-homed vESes on a single physical port, such as a single ENNI. (R1b) The PE MUST support a combination of single-homed vESes and Single-Active multi-homed vESes simultaneously on a single physical port, such as a single ENNI. Throughout this document, Single-Active multi-homed vESes will be referred to as Single-Active vESes. (R1c) The PE MAY support All-Active multi-homed vESes on a single physical port. Throughout this document, All-Active multi-homed vESes will be referred to as All-Active vESes. (R1d) The PE MAY support a combination of All-Active vESes along with other types of vESes on a single physical port. (R1e) A Multi-Homed vES, whether Single-Active or All-Active, can span across two or more ENNIs on any two or more PEs.

Many vESes of different types can be aggregated on a single physical port on a PE device and some of these vESes can belong to the same service instance (e.g., EVI). This translates into the need for supporting local switching among the vESes for the same service instance on the same physical port (e.g., ENNI) of the PE. (R3a) A PE device that supports the vES function MUST support local switching among different vESes associated with the same service instance on a single physical port. For instance, in Figure 1, PE1 must support local switching between CE11 and CE12, which are mapped to two single-homed vESes on ENNI1. In the case of Single-Active vESes, the local switching is performed among active EVCs associated with the same service instance on the same ENNI.

A physical port, such as an ENNI of a PE device, can aggregate numerous EVCs, each associated with a vES. An EVC may carry one or more VLANs. Typically, an EVC carries a single VLAN and is therefore associated with a single broadcast domain. However, there are no restrictions preventing an EVC from carrying multiple VLANs. (R4a) An EVC can be associated with a single broadcast domain, such as in a VLAN-based service or a VLAN bundle service. (R4b) An EVC MAY be associated with several broadcast domains, such as in a VLAN-aware bundle service. Similarly, a PE can aggregate multiple LSPs and PWs. In the case of individual PWs per vES, typically, a PW is associated with a single broadcast domain, although there are no restrictions preventing a PW from carrying multiple VLANs if the PW is configured in Raw mode. (R4c) A PW can be associated with a single broadcast domain, such as in a VLAN-based service or a VLAN bundle service. (R4d) An PW MAY be associated with several broadcast domains, such as in a VLAN-aware bundle service.

Section 8.5 of outlines the default procedure for DF election in EVPN, which is also applied in and . elaborates on additional procedures for DF election in EVPN. These DF election procedures are performed at the granularity of (ESI, Ethernet Tag). In the context of a vES, the same EVPN default procedure for DF election is applicable, but at the granularity of (vESI, Ethernet Tag). In this context, the Ethernet Tag is represented by an I-SID in PBB-EVPN and by a VLAN ID (VID) in EVPN. As described in , this default procedure for DF election at the granularity of (vESI, Ethernet Tag) is also known as "service carving." The goal of service carving is to evenly distribute the DFs for different vESes among various PEs, thereby ensuring an even distribution of traffic across the PEs. The following requirements are applicable to the DF election of vESes for (PBB-)EVPN. (R5a) A PE that supports vES function, MUST support a vES with m EVCs among n ENNIs belonging to p PEs in any arbitrary order; where n >= p >= m >=2. For example, if there is a vES with 2 EVCs and there are 5 ENNIs on 5 PEs (PE1 through PE5), then vES can be dual homed to PE2 and PE4 and the DF election must be performed between PE2 and PE4. (Rbc) Each vES MUST be identified by its own virtual ESI (vESI).

To detect the failure of an individual EVC and subsequently perform DF election for its associated vES as a result of this failure, each EVC should be monitored independently. (R6a) Each EVC SHOULD be independently monitored for its operational health. (R6b) A failure in a single EVC, among many aggregated on a single physical port or ENNI, MUST trigger a DF election for its associated vES.

(R7a) Failure and failure recovery of an EVC for a Single-homed vES SHALL NOT impact any other EVCs within its service instance or any other service instances. In other words, for PBB-EVPN, it SHALL NOT trigger any MAC flushing both within its own I-SID as well as other I-SIDs. (R7b) In case of All-Active vES, failure and failure recovery of an EVC for that vES SHALL NOT impact any other EVCs within its service instance or any other service instances. In other words, for PBB-EVPN, it SHALL NOT trigger any MAC flushing both within its own I-SID as well as other I-SIDs. (R7c) Failure and failure recovery of an EVC for a Single-Active vES SHALL impact only its own service instance. In other words, for PBB- EVPN, MAC flushing SHALL be limited to the associated I-SID only and SHALL NOT impact any other I-SIDs. (R7d) Failure and failure recovery of an EVC for a Single-Active vES MUST only impact C-MACs associated with multi-homed device/network for that service instance. In other words, MAC flushing MUST be limited to single service instance (I-SID in the case of PBB-EVPN) and only C-MACs for Single-Active multi-homed device/network.

Since many EVCs (and their associated vESes) are aggregated via a single physical port (e.g., ENNI), then the failure of that physical port impacts many vESes and triggers equally many ES route withdrawals. Formulating, sending, receiving, and processing such large number of BGP messages can introduce delay in DF election and convergence time. As such, it is highly desirable to have a mass&nbhy;withdraw mechanism similar to the one in for withdrawing many Ethernet A-D per ES routes. (R8a) There SHOULD be a mechanism equivalent to EVPN mass&nbhy;withdraw such that upon an ENNI failure, only a single BGP message is needed to indicate to the remote PEs to trigger DF election for all impacted vES associated with that ENNI.

The solutions described in and are leveraged as&nbhy;is with the modification that the ESI assignment is performed for an EVC or a group of EVCs or LSPs/PWs instead of a link or a group of physical links. In other words, the ESI is associated with a virtual ES (vES), hereby referred to as vESI. In the EVPN solution, the overall procedures remain consistent, with the primary difference being the handling of physical port failures that can affect multiple vESes. Sections and describe the procedures for managing physical port or link failures in the context of EVPN. In a typical multi-homed setup, MAC addresses learned behind a vES are advertised using the ESI associated with the vES, referred to as the vESI. EVPN aliasing and mass-withdraw operations are conducted with respect to the vES identifier. Specifically, the Ethernet Auto-Discovery (A-D) routes for these operations are advertised using the vESI instead of the ESI. For PBB-EVPN solution, the main change is with respect to the B-MAC address assignment which is performed similar to what is described in section 7.2.1.1 of with the following refinements: One shared B-MAC address SHOULD be used per PE for the single&nbhy;homed vESes. In other words, a single B-MAC is shared for all single&nbhy;homed vESes on that PE. One shared B-MAC address SHOULD be used per PE per physical port (e.g., ENNI) for the Single-Active vESes. In other words, a single B-MAC is shared for all Single-Active vESes that share the same ENNI. One shared B-MAC address MAY be used for all Single-Active vESes on that PE. One B-MAC address SHOULD be used per set of EVCs representing an All-Active vES. In other words, a single B-MAC address is used per vES for All-Active scenarios. A single B-MAC address MAY also be used per vES per PE for Single- Active scenarios.

The procedure for service carving for virtual Ethernet Segments is almost the same as the ones outlined in section 8.5 of and except for the fact that ES is replaced with vES. For the sake of clarity and completeness, the default DF election procedure of is repeated below with the necessary changes: When a PE discovers the vESI or is configured with the vESI associated with its attached vES, it advertises an Ethernet Segment route with the associated ES-Import extended community attribute. The PE then starts a timer (default value = 3 seconds) to allow the reception of Ethernet Segment routes from other PE nodes connected to the same vES. This timer value MUST be same across all PEs connected to the same vES. When the timer expires, each PE builds an ordered list of the IP addresses of all the PE nodes connected to the vES (including itself), in increasing numeric value. Each IP address in this list is extracted from the "Originator Router's IP address" field of the advertised Ethernet Segment route. Every PE is then given an ordinal indicating its position in the ordered list, starting with 0 as the ordinal for the PE with the numerically lowest IP address. The ordinals are used to determine which PE node will be the DF for a given EVPN instance on the vES using the following rule: Assuming a redundancy group of N PE nodes, the PE with ordinal i is the DF for an EVPN instance with an associated Ethernet Tag value of V when (V mod N) = i. It should be noted that using "Originator Router's IP address" field in the Ethernet Segment route to get the PE IP address needed for the ordered list, allows for a CE to be multi&nbhy;homed across different ASes if such need ever arises. The PE that is elected as a DF for a given EVPN instance will unblock traffic for that EVPN instance. Note that the DF PE unblocks all traffic in both ingress and egress directions for Single-Active vES and unblocks multi&nbhy;destination in egress direction for All-Active Multi-homed vES. All non-DF PEs block all traffic in both ingress and egress directions for Single-Active vES and block multi&nbhy;destination traffic in the egress direction for All-Active vES. In case of an EVC failure, the affected PE withdraws its Virtual Ethernet Segment route if there are no more EVCs associated to the vES in the PE. This will re-trigger the DF Election procedure on all the PEs in the Redundancy Group. For PE node failure, or upon PE commissioning or decommissioning, the PEs re-trigger the DF Election procedure across all affected vESes. In case of a Single-Active, when a service moves from one PE in the Redundancy Group to another PE because of DF re-election, the PE, which ends up being the elected DF for the service, MUST trigger a MAC address flush notification towards the associated vES if the multi-homing device is a bridge or the multi-homing network is an Ethernet bridged network. For LSP-based and PW-based vES, the non-DF PE SHOULD signal PW-status 'standby' to the Aggregation PE (e.g., AG1 and AG2 in Figure 2), and a new DF PE MAY send an LDP MAC withdraw message as a MAC address flush notification. It should be noted that the PW-status is signaled for the scenarios where there is a one-to-one mapping between EVI (EVPN instance) and the PW.

Physical ports (e.g. ENNI) which aggregate many EVCs are 'colored' to enable the grouping schemes described below. By default, the MAC address of the corresponding port (e.g. ENNI) is used to represent the 'color' of the port, and the EVPN Router's MAC Extended Community defined in is used to signal this color. The difference between coloring mechanism for EVPN and PBB-EVPN is that for EVPN, the extended community is advertised with the Ethernet A-D per ES route whereas for PBB-EVPN, the extended community is advertised with the B-MAC route. The subsequent sections detailing Grouping of Ethernet Auto-Discovery (A-D) per ES and Grouping of B-MAC addresses will be essential for addressing port failure handling, as discussed in Sections , , and .

When a PE discovers the vESI or is configured with the vESI associated with its attached vES, an Ethernet-Segment route and Ethernet A-D per ES route are generated using the vESI identifier. These Ethernet-Segment and Ethernet A-D per ES routes specific to each vES are colored with an attribute representing their association to a physical port (e.g. ENNI). The corresponding port 'color' is encoded in the EVPN Router's MAC Extended Community defined in and advertised along with the Ethernet Segment and Ethernet A-D per ES routes for this vES. The color (which is the MAC address of the port) MUST be unique. The PE also constructs a special Grouping Ethernet A-D per ES route which represents all the vES associated with the port (e.g. ENNI). The corresponding port 'color' is encoded in the ESI field. For this encoding, Type 3 ESI () is used with the MAC field set to the color (MAC address) of the port and the 3-octet local discriminator field set to 0xFFFFFF. The ESI label extended community () is not relevant to Grouping Ethernet A-D per ES route. The label value is not used for encapsulating BUM (Broadcast, Unknown-unicast, Multicast) packets for any split-horizon function. The ESI label extended community MUST NOT be added to Grouping Ethernet A-D per ES route and MUST be ignored on receiving PE. The Grouping Ethernet Auto-Discovery (A-D) per ES route is advertised with a list of Route Targets corresponding to the affected service instances. If the number of associated Route Targets exceeds the capacity of a single route, multiple Grouping Ethernet A-D per ES routes are advertised accordingly.

In PBB-EVPN, particularly when there are a large number of service instances (i.e., I-SIDs) associated with each EVC, the PE device MAY assign a color attribute to each vES B-MAC route, indicating their association with a physical port (e.g., an ENNI). The corresponding port 'color' is encoded in the EVPN Router's MAC Extended Community defined in and advertised along with the B-MAC for this vES in PBB-EVPN. The PE MAY then also construct a special Grouping B-MAC route which represents all the vES associated with the port (e.g. ENNI). The corresponding port 'color' is encoded directly into this special Grouping B-MAC route.

There are several failure scenarios to consider such as: CE uplink port failure Ethernet Access Network failure PE access-facing port or link failure PE node failure PE isolation from IP/MPLS network The solutions outlined in , , and provide protection against failures as described in these respective references. In the context of these solutions, the presence of vESes introduces an additional failure scenario beyond those already considered, specifically the failure of individual EVCs. Addressing vES failure scenarios necessitates the independent monitoring of EVCs or PWs. Upon detection of failure or service restoration, appropriate DF election and failure recovery mechanisms must be executed. is used for monitoring EVCs and upon failure detection of a given EVC, DF election procedure per is executed. For PBB-EVPN, some extensions are needed to handle the failure and recovery procedures of to meet the above requirements. These extensions are described in the next section. and are used for monitoring the status of LSPs and/or PWs associated to vES.

In , when a DF PE connected to a Single-Active multi&nbhy;homed Ethernet Segment loses connectivity to the segment, due to link or port failure, it signals to the remote PEs to invalidate all MAC addresses associated with that Ethernet Segment. This is done by means of a mass&nbhy;withdraw message, by withdrawing the Ethernet A-D per ES route. It should be noted that for dual-homing use cases where there is only a single backup path, MAC invalidating can be avoided by the remote PEs as they can update their next hop associated with the affected MAC entries to the backup path per procedure described in section 8.2 of . In case of an EVC failure which impacts a single vES, this same EVPN procedure is used. In this case, the mass&nbhy;withdraw is conveyed by withdrawing the Ethernet A-D per vES route carrying the vESI representing the failed EVC. The remote PEs upon receiving this message perform the same procedures outlined in section 8.2 of .

In when a PE connected to a Single-Active Ethernet Segment loses connectivity to the segment, due to link or port failure, it signals the remote PE to flush all C-MAC addresses associated with that Ethernet Segment. This is done by updating the advertised a B-MAC route's MAC Mobility Extended community. In case of an EVC failure that impacts a single vES, if the above PBB-EVPN procedure is used, it results in excessive C-MAC flushing because a single physical port can support large number of EVCs (and their associated vESes) and thus updating the advertised B-MAC corresponding to the physical port, with MAC mobility Extended community, will result in flushing C-MAC addresses not just for the impacted EVC but for all other EVCs on that port. To reduce the scope of C-MAC flushing to only the impacted service instances (the service instance(s) impacted by the EVC failure), the PBB-EVPN C-MAC flushing needs to be adapted on a per service instance basis (i.e., per I-SID). introduces B-MAC/I-SID route where existing PBB-EVPN B-MAC route is modified to carry an I-SID in the "Ethernet Tag ID" field instead of NULL value. This field indicates to the receiving PE, to flush all C-MAC addresses associated with that I-SID for that B-MAC. This C-MAC flushing mechanism per I-SID SHOULD be used in case of EVC failure impacting a vES. Since typically an EVC maps to a single broadcast domain and thus, a single service instance, the affected PE only needs to advertise a single B-MAC/I-SID route. However, if the failed EVC carries multiple VLANs each with its own broadcast domain, then the affected PE needs to advertise multiple B-MAC/I-SID routes - one for each VLAN (broadcast domain) - i.e., one for each I-SID. Each B-MAC/I-SID route basically instructs the remote PEs to perform flushing for C-MACs corresponding to the advertised B-MAC only for the advertised I-SID. The C-MAC flushing based on B-MAC/I-SID route works fine when there are only a few VLANs (e.g., I-SIDs) per EVC. However if the number of I-SIDs associated with a failed EVC is large, then it is RECOMMENDED to assign a B-MAC per vES and upon EVC failure, the affected PE simply withdraws this B-MAC message to other PEs.

When many EVCs are aggregated via a single physical port on a PE, where each EVC corresponds to a vES, then the port failure impacts all the associated EVCs and their corresponding vESes. If the number of EVCs corresponding to the Single-Active vESes for that physical port is in thousands, then thousands of service instances (I-SIDs) are impacted. In such failure scenarios, the following two MAC flushing mechanisms per can be performed. If the MAC address of the physical port is used for PBB encapsulation as B-MAC SA, then upon the port failure, the PE MUST use the EVPN MAC route withdrawal message to signal the flush. If the PE shared MAC address is used for PBB encapsulation as B-MAC SA, then upon the port failure, the PE MUST re-advertise this MAC route with the MAC Mobility Extended Community to signal the flush. The first method is recommended because it reduces the scope of flushing the most. As noted above, the advertisement of the extended community along with B-MAC route for coloring purposes is optional and only recommended when there are many vESes per physical port and each vES is associated with very large number of service instances (i.e., large number of I-SIDs). If there are large number of service instances (i.e., I-SIDs) associated with each EVC, and if there is a B-MAC assigned per vES as recommended in the above section, then to handle port failure efficiently, the following extensions are added to the baseline PBB-EVPN mechanism: Each vES MAY be colored with a MAC address representing the physical port like the coloring mechanism for EVPN. In other words, each B-MAC representing a vES is advertised with the 'color' of the physical port per . The receiving PEs take note of this color being advertised along with the B-MAC route and for each such color, create a list of vESes associated with this color. The PE MAY advertise a special Grouping B-MAC route for that color (consisting by default of port MAC address), which represents all the vES associated with the port. Upon a port failure (e.g., ENNI failure), the PE MAY send a mass&nbhy;withdraw message by withdrawing the Grouping B-MAC route. When this message is received, the remote PE MAY detect the special vES mass&nbhy;withdraw message by identifying the Grouping B-MAC route. The remote PEs MAY then access the list created in (1) for the specified color, and flush all C-MACs associated with the failed physical port.

As described above, when many EVCs are aggregated via a physical port on a PE, and where each EVC corresponds to a vES, then the port failure impacts all the associated EVCs and their corresponding vESes. Two actions must be taken as the result of such port failure: For EVPN initiate mass&nbhy;withdraw procedure for all vESes associated with the failed port to invalidate MACs and for PBB-EVPN flush all C-MACs associated with the failed port across all vESes and the impacted I-SIDs DF election for all impacted vESes associated with the failed port already describes how to perform mass&nbhy;withdraw for all affected vESes and invalidating MACs using a single BGP withdrawal of the Grouping Ethernet A-D per ES route. describes how to only flush C-MAC address associated with the failed physical port (e.g., optimum C-MAC flushing) as well as, optionally, the withdrawal of a Grouping B-MAC route. This section describes how to perform DF election in the most optimal way - e.g., to trigger DF election for all impacted vESes (which can be very large) among the participating PEs via a single BGP message as opposed to sending large number of BGP messages (one per vES). This section assumes that the MAC flushing mechanism described in is used and route coloring is used.

As discussed in , it is highly desirable to have a mass withdraw mechanism similar to the one in . Although such an optimization is desirable, it is OPTIONAL. If the optimization is implemented, the following describes the procedure: When a vES is configured, the PE advertises the Ethernet Segment route for this vES with a color that corresponds to the associated physical port. All receiving PEs within the redundancy group record this color and compile a list of vESes associated with it. Additionally, the PE advertises a Grouping Ethernet A-D per ES for EVPN, and a Grouping B-MAC for PBB-EVPN, which corresponds to the color and vES grouping. In the event of a port failure, such as an ENNI failure, the PE withdraws the previously advertised Grouping Ethernet A-D per ES or Grouping B-MAC associated with the failed port. The PE should prioritize sending these Grouping route withdrawal messages over the withdrawal of individual vES routes affected by the failure. For instance, as depicted in Figure 5, when the physical port associated with ENNI3 fails on PE2, it withdraws the previously advertised Grouping Ethernet A-D per ES route. Upon receiving this withdrawal message, other multi-homing PEs (such as PE1 and PE3) recognize that the vESes associated with CE1 and CE3 are impacted, based on the associated color, and thus initiate the DF election procedure for these vESes. Furthermore, remote PEs (such as PE4), upon receiving this withdrawal message, initiate the failover procedure for the vESes associated with CE1 and CE3, and switch to the other PE for each vES redundancy group. On reception of Grouping Ethernet A-D per ES or Grouping B-MAC route withdrawal, other PEs in the redundancy group initiate DF election procedures across all their affected vESes. The PE with the physical port failure (ENNI failure), sends vES route withdrawal for every impacted vES. The other PEs upon receiving these messages, clear up their BGP tables. It should be noted the vES route withdrawal messages are not used for executing DF election procedures by the receiving PEs when Grouping Ethernet A-D per ES or Grouping B-MAC withdrawal has been previously received.

The authors would like to thank Mei Zhang, Jose Liste, and Luc Andre Burdet for their reviews of this document and feedback.

All the security considerations in and apply directly to this document because this document leverages the control and data plane procedures described in those documents. This document does not introduce any new security considerations beyond that of and because advertisements and processing of Ethernet Segment route for vES in this document follows that of physical ES in those RFCs.

This document requests no actions from IANA.